Revo LC Error Codes

Revo LC Error Codes, Elevator Control Cards Error Codes

ERROR NO 01:

Error Name: Cabin Communication Error

Error Description: Can-Bus line between the Main Card and the Cabin Card does not communicate. It is selected in elevator systems.

*Check Can1 Can-Bus Line.

*Make sure that GND passes on the right and left side of the live and live cables in the flexible cable.

ERROR NO 02:

Error Name: Floor Communication Error

Error Description: Can-Bus line between the Main Board and Floor Serial Cards is not communicating.

*Check Can2 Can-Bus Line.

*Can2 Make sure the termination resistor at the end of the Can-Bus line is installed.

ERROR NO 03:

Error Name: Door Closing Error

Error Description: The door did not reach the closing limit at the end of the lock waiting period.

*Check the door limit (if any) and door lock.

*Check Lock Waiting Time (See B05).

*Check the Door closing A-B(A3-B3) relays on the cabin board.

ERROR NO 04:

Error Name: Door opening error

Error Description: The door opening signal came, but 120-125-130-135-140 was not interrupted.

*Check the door opening/closing connection.

*Check the Door opening A-B(A5-B5) relays on the cabin board.

ERROR NO 05:

Error Name: Operation out of region.

Error Description: The elevator went out of the working zone.

*Check the encoder signal.

*Check the placement of floor magnets.

ERROR NO 06:

Error Name: High Speed ​​Duration Error.

Error Description: In motion., the next floor could not be reached within the specified time.

*Check High Speed ​​Time (See B06).

*Make sure the floor magnets are placed correctly.

ERROR NO 07:

Error Name: ML1 ML2 Error in Docking.

Error Description: No floor magnet found in drift zone

*Check magnet placement.

*Check ramp DO-D1-D2 (See I02-03-04) values.

*Do well recognition again.

ERROR NO 08:

Error Name: Encoder counting error.

Error Description: Encoder counting error.

*Check encoder connections.

ERROR NO 09:

Error Name: Out of region door opening error.

Error Description: There is no ML1-ML2 input in the door opening zone.

*Check ML1-ML2 switch.

*Check floor magnet placement.

ERROR NO 10:

Error Name: Out of zone door closing error.

Error Description: There is no ML1-ML2 input in the door closing zone.

*Check ML1-ML2 switch.

*Check floor magnet placement.

ERROR NO 11:

Error Name: Error 120 in movement.

Error Description: External door safety cut off during movement.

*Check the inner door connection.

ERROR NO 12:

Error Name: Error 125 in transaction.

Error Description: External door safety cut off during movement.

*Check the inner door connection.

ERROR NO 13:

Error Name: Error 130 in movement.

Error Description: External door safety cut off during movement.

*Check the inner door connection.

ERROR NO 14:

Error Name: Error 120 while stopping.

Error Description: Disconnection of standby safety circuits.

*Check stop connections.

ERROR NO 15:

Error Name: KRC error 1.

Error Description: Contactor feedback detected while in motion.

*Check the closed contacts of the contactors.

ERROR NO 16:

Error Name: KRC error 2.

Error Description: Contactor feedback was interrupted while stopping.

*Check the closed contacts of the contactors.

ERROR NO 17:

Error Name: UCM error.

Error Description: The cabin moved in the door opening area.

*Check the magnet inputs.

*Check the door area.

ERROR NO 18:

Error Name: UCM contact error gearless.

Error Description: Controls the brake switch while moving and stopping.

*Check brake switch connections.

ERROR NO 19:

Error Name: UCM contact error gear.

Error Description: Controls the regulator coil switch while moving and stopping.

*Check the switch connection of the regulator coil.

ERROR NO 20:

Error Name: No internal door and external door safety circuit error detected.

Error Description: No internal door and external door safety circuit error detected.

*Check the door safety contacts.

*If there is no door limit, check the door closing time (See C06).

ERROR NO 21:

Error Name: Door bridging error

Error Description: Door did not open at the end of the door opening time detection error.

*Check door connections.

*Check the door safety contacts.

ERROR NO 22:

Error Name: Door bridging error.

Error Description: Doors not opening or bridging in door safety circuits detected.

*Check the door opening-closing outputs.

ERROR NO 23:

Error Name: Upper limit error.

Error Description: Upper upper limit breaker 818 is disabled while in motion.

*Check the upper limit roller switch.

ERROR NO 24:

Error Name: Lower limit error.

Error Description: Upper lower limit breaker 817 has tripped during movement.

*Check the lower limit roller switch.

ERROR NO 25:

Error Name: Inverter error.

Error Description: DFI input is disabled, inverter error detected.

*Check inverter settings.

ERROR NO 26:

Error Name: PTC temperature error.

Error Description: Motor thermistor error detected.

*Check engine temperature.

ERROR NO 27:

Error Name: Timeout

Error Description: Program processing timeout error detected.

*Check time settings.

ERROR NO 28:

Error Name: UPS recovery error.

Error Description: Recovery could not be performed after the UPS recovery maximum time (See H03).

*Check UPS power.

*Check the recovery maximum time (See H03).

ERROR NO 29:

Error Name: Lower-Upper limit is active

Error Description: Lower and upper breaker limits (817-818) were cut at the same time error was detected.

*Check roller limit breakers (817-818).

ERROR NO 30:

Error Name: Leveling error.

Error Description: Leveling could not be done within the leveling time (See B32).

*Check leveling time (See B32).

ERROR NO 31:

Error Name: ML1-ML2 missing error.

Error Description: ML1-ML2 detection error in door opening zone.

*Check the floor stop (ML1-ML2) switch.

*Check the deceleration ramps Ramp DO-D1-D2 (See I02-03-04).

ERROR NO 32:

Error Name: Overload Error

Error Description: Error occurring in case of overload.

*Check the cabin load and overload sensor input (804).

ERROR NO 33:

Error Name: Maximum Load Error

Error Description: Occurs in maximum load condition.

ERROR NO 34:

Error Name: Target Lost error.

Error Description: The destination of the elevator has disappeared.

*Logic error, contact the supplier.

ERROR NO 35:

Error Name: ML1-ML2 missing error at startup.

Error Description: ML1-ML2 could not be seen when the elevator would start moving.

*Check the floor stop (ML1-ML2) switch.

ERROR NO 36:

Error Name: M0 Counter Error.

Error Description: M0 Counter Error.

*Check M0 inputs and magnet placement.

ERROR NO 37:

Error Name: Duplex Communication Error.

Error Description: Communication error in duplex system.

*Check Can3 Can-Bus communication line.

ERROR NO 38:

Error Name: No Movement Error.

Error Description: Movement did not occur even though a movement command was given

*Check inverter settings.

ERROR NO 39:

Error Name: 24V Supply Error.

Error Description: Supply voltage is below 19V.

*Measure 24 volt supply voltage and check the outputs.

ERROR NO 40:

Error Name: Low Speed ​​Duration Error.

Error Description: During docking, the floor could not be reached within the specified time.

*Check Low Speed ​​Time (See B07).

*Make sure the floor magnets are placed correctly.

ERROR NO 41:

Error Name: Phase Sequence Error.

Error Description: The order of RST high voltage inputs is incorrect.

*Check the order of RST high voltage inputs.

ERROR NO 42:

Error Name: Missing Phase Error.

Error Description: RST high voltage inputs have missing phase.

*Check RST high voltage inputs.

ERROR NO 43:

Error Name: Error 135 in Transaction.

Error Description: Interior door opened during movement.

*Check 135 high voltage input.

ERROR NO 44:

Error Name: Error 140 in movement.

Error Description: Interior door opened during movement.

*Check 140 high voltage input.

ERROR NO 45:

Error Name: Error 45 Reserved.

Error Description: Reserved.

* Reserved.

ERROR NO 46:

Error Name: Error 46 Reserved.

Error Description: Reserved.

* Reserved.

ERROR NO 47:

Error Name: Error 47 Reserved.

Error Description: Reserved.

* Reserved.

ERROR NO 48:

Error Name: Error 48 Reserved.

Error Description: Reserved.

* Reserved.

ERROR NO 49:

Error Name: Upstairs Error.

Error Description: The elevator could not find the floor during its upward movement to find the floor.

*Check well magnet placement and 817-818 signal inputs.

ERROR NO 50:

Error Name: Error 50 Reserved.

Error Description: Reserved.

* Reserved